Updated Oct 27, 2026· 8 min read

Key takeaways

  • A regulator and hose, if not included, rated for the burner.
  • Tongs matched to your stock thickness, a hammer and an anvil or anvil substitute.
  • A way to judge temperature. Kiln Frog suggests a thermocouple combo for reducing guesswork when forging and heat treating, and a magnet is a traditional low-cost check for critical temperature.
  • Rigidizer and kiln wash for ceramic lining, and a respirator.
  • A quench tank and appropriate quenchant for your steel type, with a fire plan.

For a beginner who wants to forge knives, a single-burner forge with a small chamber, such as the Atlas Knife and Tool Atlas Forge or the NC Tool Whisper Baby, is the usual recommendation, because blades are long and thin and a small chamber heats quickly and uses little propane. Makers who plan to forge larger blades, weld pattern steel, or work for hours at a time may prefer a two- or three-burner forge such as the Devil Forge DFPROF3+2D or a Majestic knifemaker model, and budget buyers often look at lower-cost imports such as VEVOR, accepting the trade-offs in insulation and durability.

This guide covers how gas forges work, what the makers state about their chambers, burners and insulation, how to match a forge to the blades you want to make, and the safety practices that matter before you light anything. It draws on maker pages where available and on independent roundups, and it attributes claims to those sources. Several of the roundups are affiliate-style sites, and some maker pages did not display full specifications, so figures below are those the sources state, not independent measurements.

How a gas forge for knife making works

A propane forge is an insulated chamber with one or more burners that feed a mixture of fuel and air into the chamber, where the flame heats the steel. The chamber is lined with ceramic fibre blanket, cast refractory, or both. Blades are heated to forging temperature, hammered on an anvil, reheated, and later heat treated. A forge for knives needs even heat along a bar roughly 8 to 12 inches long, enough power to reach forging and, if you plan to forge weld, welding temperatures, and an opening wide enough to pass a blade in and out safely.

Burner count and chamber size

One burner is enough for most knife work. A small chamber, around 2.5 to 3 inches across and 7 to 11 inches long, heats fast and burns less fuel. More burners and a bigger chamber add capability for longer blades, bundles of layered steel, and general blacksmithing, but they cost more and burn considerably more propane. A second door lets you pass longer stock through the forge.

Insulation: ceramic wool versus cast refractory

Ceramic fibre blanket heats and cools quickly and keeps the forge light, but it is fragile and sheds fibres, so it is normally coated with a rigidizer and a kiln wash and handled with a respirator. Cast refractory, such as the Kastolite 50-25 Plus that Kiln Frog says Atlas uses, is denser and more durable. Kiln Frog states that this refractory outlasts the ceramic wool used in cheaper forges.

At a glance: forges named by reviewers

Forge Burners Stated chamber and temperature Insulation Best for Limits
Atlas Knife and Tool Atlas Forge One atmospheric burner 2.5 in diameter by 11 in long, up to 2,500 F per Kiln Frog Kastolite 50-25 Plus cast refractory, stainless shell Beginner and intermediate knifemakers Small chamber limits long blades such as swords
Atlas Firestorm Two burners 6 in by 13 in, about 2,400 F per Kiln Frog, 42 lb Kastolite cast refractory General blacksmithing Overkill for knives, doubles fuel use
NC Tool Whisper Baby One venturi-style burner Reported 3 x 7 x 6.5 in chamber Not detailed in sources Quiet, fuel-efficient long-term use Higher cost, small capacity
NC Tool Knifemaker Forge and Knifemaker 21 Not detailed on maker page Insulated doors; convertible to natural gas per roundup Not detailed Dedicated knifemaking Premium cost, specs not listed on the page consulted
Devil Forge DFPROF3+2D Three Rated 240,000 BTU and 2,500 F, two doors, 16-gauge steel body Not detailed Larger blades, forge welding One roundup does not recommend it for absolute beginners
Majestic Knifemaker (Economy, dual burner) Two Described as a compact two-burner with a large interior Ceramic fibre Beginners planning rapid progress More fuel, larger footprint
VEVOR and similar imports One or two Varies Typically ceramic wool Tight budgets Reviewers describe them as budget picks with durability trade-offs

The main options in detail

Atlas Knife and Tool Atlas Forge

Atlas is the brand most often named for beginner knifemakers. According to Kiln Frog, the Atlas Forge is a single-burner forge with a 2.5-inch by 11-inch chamber, Kastolite 50-25 Plus cast refractory, a stainless steel shell, a maximum of about 2,500 degrees Fahrenheit, and an included regulator and hose. A portable version is listed at about 19.8 lb, so one person can set it up. The same source says the smaller chamber limits longer projects such as swords. Another roundup names an Atlas Mini with the same stated chamber dimensions, so confirm which model you are looking at. One roundup says Atlas and Devil Forge are popular with professional bladesmiths, including those who appear on television forging competitions.

NC Tool Whisper Baby and Knifemaker forges

NC Tool is a long-established maker whose forges are built in the United States. A roundup describes the Whisper Baby as a single-burner, venturi-style forge with a chamber of about 3 by 7 by 6.5 inches, known for quiet operation and low fuel use, and notes its higher initial price. NC Tool also lists a dedicated Knifemaker Forge and a Knifemaker Forge 21 on its site, but the page consulted did not list chamber sizes or temperature ratings, and a roundup says the Knifemaker model has insulated doors and can be converted to natural gas. Contact the maker for full specifications before buying.

Devil Forge and Majestic

Devil Forge’s DFPROF3+2D is described by one roundup as an editor’s choice, rated at 240,000 BTU and 2,500 degrees Fahrenheit, with two doors, a 16-gauge steel body, and tongs, gloves and rigidizer included. The same roundup says it is not recommended for absolute beginners because of its size and fuel use. A five-burner DFPROF5 and a three-burner DFPROFK3 with double insulation are also mentioned. Majestic Forge is the brand most commonly seen on television forging competitions, and its dual-burner knifemaker model is described as spacious for a compact forge, with the trade-off of higher fuel consumption.

Budget imports

VEVOR and similar brands are the budget picks in several roundups. They usually pair ceramic fibre insulation with a thinner shell. They allow you to start forging at a lower cost, but reviewers describe them as less durable than cast-refractory forges, and instructions and burner quality vary. If you choose one, plan on coating the interior with rigidizer and a high-temperature wash, as the manual advises.

Matching the forge to the knives you make

Project Forge size that suits it Notes
Paring, utility and small kitchen knives Single burner, small chamber Fast heating, minimal fuel
Hunting and chef’s knives up to about 10-inch blades Single burner with 7-11 inch chamber, or compact two-burner Even heat along the blade matters more than power
Long kitchen knives, machetes, short swords Two doors or larger chamber Pass-through stock avoids bending the bar
Forge-welded pattern steel Forge rated near 2,500 F with durable lining Welding heat wears ceramic wool faster

Safety and setup notes

Propane forges involve open flame, hot metal, pressurised fuel and carbon monoxide, so follow the maker’s manual and consult local fire rules. Kiln Frog advises infrared-rated safety glasses, leather protective gear, a fire extinguisher, and never running the forge indoors without serious ventilation, with about 10 feet of clearance from walls and flammable materials. Use the regulator and hose rated for the forge, check connections for leaks with soapy water, keep the cylinder upright and away from the flame, and shut the cylinder valve when you are finished. Wear a respirator when handling ceramic fibre, and wear hearing protection around a loud forge. If you smell gas or see damage to hoses or fittings, stop and have it repaired by a qualified person. Check whether your home insurance or local rules limit forging in garages or sheds.

Accessories you will need

  • A regulator and hose, if not included, rated for the burner.
  • Tongs matched to your stock thickness, a hammer and an anvil or anvil substitute.
  • A way to judge temperature. Kiln Frog suggests a thermocouple combo for reducing guesswork when forging and heat treating, and a magnet is a traditional low-cost check for critical temperature.
  • Rigidizer and kiln wash for ceramic lining, and a respirator.
  • A quench tank and appropriate quenchant for your steel type, with a fire plan.

Pick X if… decision table

If you… Pick Why
Want a durable first forge for knives Atlas Forge Cast refractory, included regulator and hose, popular with knifemakers
Value quiet and fuel economy and have the budget NC Tool Whisper Baby Venturi burner, low fuel use per reviewers
Plan to forge weld or make longer blades Devil Forge DFPROF3+2D or a Majestic two-burner Two doors, higher heat output
Need a lower-cost way to start VEVOR-type forge Budget price, with durability trade-offs
Do general blacksmithing as well Atlas Firestorm Wider chamber for scrollwork and horseshoes

Alternatives to a gas forge

Solid-fuel forges using charcoal or coal need no regulator but demand skill with fire management and produce smoke. Electric kilns and forges, used by many bladesmiths for heat treating, offer precise temperature control but are not designed for open forging. Some beginners start with stock removal, grinding a blade from bar steel without forging, which needs a belt grinder but no forge. Each approach has different safety needs, so follow the maker’s manual and local rules.

Frequently Asked Questions

How many burners do I need to forge knives?

One is enough for most blades. A single burner heats a small chamber quickly and uses less propane. A second burner helps with longer blades, larger stock and forge welding.

Is ceramic wool or cast refractory better?

Cast refractory is denser and more durable, which Kiln Frog says helps it outlast the ceramic wool in cheaper forges. Ceramic wool heats and cools quickly and keeps weight down but is fragile and needs a coating and respiratory protection.

What temperature does a knife forge need to reach?

Makers rate popular knife forges at about 2,400 to 2,500 degrees Fahrenheit, which covers forging temperatures for most steels and forge welding for some. Use the maker’s rating and your steel’s data sheet, and measure temperature with a suitable tool.

Can I use a gas forge in a garage?

Only with serious ventilation, and some makers and fire authorities advise against it. Propane forges produce carbon monoxide, so work outdoors or in a well-ventilated space and keep flammables away. Follow the manual and local rules.

Do I need a thermocouple?

No, but it helps. Many knifemakers use a magnet and colour to judge heat. A thermocouple or pyrometer reduces guesswork, particularly for heat treating.

How much propane does a knife forge use?

Fuel use depends on burner count, chamber size and run time. Roundups say small single-burner forges are efficient, while multi-burner forges consume noticeably more. Check the maker’s burner specification for the exact figures.

T
The Fish Butcher Editorial Team
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Gas Forges for Knife Making: Top Picks…Check price on Amazon

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Prime for Young Adults

A Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.

See Prime for Young Adults
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.